Sandblasting nozzles for abrasive blast cleaning

Sandblasting nozzles

Everblast makes & supplies a comprehensive range of industrial high quality carbide sandblasting nozzles. We bring over 20 years of dedicated design, building & supply of quality industrial blast cleaning nozzles for the blast cleaning industry.

Wear resistant Sandblasting nozzles increase a sandblasting system's output pressure as well as accelerating and targeting the abrasive blast stream. Our venturi style carbide sandblast nozzles have an internal Venturi profile. The venturi nozzle's geometry can increase blast pattern size along with abrasive velocity which can result in increased kinetic energy . It is the amount of kinetic energy that effects the abrasive particles impact efficiency on the work surface (compared to a straight bore nozzle).

Blast cleaning nozzles come in many shapes and sizes giving a choice of tools for different blasting applications, to help in improving efficiency and performance.

Industrial carbide Blast cleaning nozzles are used to, for example: (1) Remove contaniments from surfaces, (2) Remove paint coatings (3) create an anchor pattern or profile to assist with coating adherence on metal surfaces (4) Remove coatings from wood surfaces, (5) Clean brick or stone work. Steel surfaces need blast cleaning before painting to remove contaminants, e.g. Bridges, locomotives, rolling stock, silos, water tanks, railcars, petrochemical plants, oil rigs, military equipment, boats and auto bodies. There are thousands of small parts that need to be blast cleaned e.g. aircraft surfaces, electronic parts, auto bodies, fiberglass products, wood surfaces, engine parts, pumps, transmissions etc. etc.

Sandblasting, media blasting, grit blasting, peening applications:

Shipyard painting and engineering work e.g. steel cleaning and profiling before paint application
Dry Blast cleaning - using dry abrasives such as coal slag, garnet, aluminum oxide to clean and add profice to hard surfaces like steel.
Shot Blasting - propelling blast cleaning media (e.g. steel shot) using centrifugal force created by a mechanical spinning device.
Soda Blast Cleaning - uses Formulated Bicarbonate of soda to clean softer surfaces e.g building walls, aluminum surfaces etc.
Steel Grit Blasting - Uses steel grit, shot etc,
Wet or slurry blasting. Used when dust control is needed especially when surface being blasted has hazardous contaminants.
Vapor blasting where the water mixing with abrasives is controlled and reduces run off.
Vacuum Blasting - used where containment is needed and recycling is considered a cost saver.
Dry Ice Blasting - used in the aviation industry
Ceramic / Pencil blast cleaning or etching
Bead blast cleaning
Shot Peening - to add additional hardness to e.g. steel surfaces.
Pipe blast cleaning both outer and inner surfaces.
Monument cleaning
Glass and stone etching
bead blasting
Heat exchanger tubes
Wooden structure surface cleaning e.g. removal of smoke and soot.
Paint removal off aircraft surfaces.
Graffiti removal
Stone and brick work cleaning
Line striping work
Watertank work
Rail car work

Blast cleaning machines and carbide nozzles:

Abrasive blast cleaning nozzles are used in conjunction with many different types of machinery e.g. Sandblasting pots, sand blasting cabinets, peening machinery, pressure washers, suction guns, slurry blast cleaning machines, machinery for stripping paint of aluminum, robotic / remote controlled blasting machines, water blast cleaning systems etc.

Blast cleaning media, flowing through a nozzle, will eventually wear away liner bore. As bore size increases it gradually reduces sandblasting system's performance by increasing demand for air. In situations where no more air is available this will result in reduced abrasive exit velocity and reduction in blasting performance and increase in costs. It is important to check nozzles before start of every shift for bore wear and/or any damage.

Contractor threads - Coarse threads:

Everblast's contractor style sandblasting nozzles for grit blasting are supplied with a choice of contractor style (2" / 50mm) or -1/4" NPSM threads. Our long venturi sandblasting nozzles are available with either 1" (25mm) or 1-1/4" (32mm) entry.

Industry Standard fine threads:

Our nozzles are available with industry standard fine threads both 1-1/4" and 3/4" NPSM

Straight Bore Nozzles and inserts:

We offer a wide range of straight bore sand blast nozzles and inserts made from tungsten carbide, Silicon carbide or boron carbide. These inserts are widely used in suction and pressure style blast cleaning guns. They are used for close up blast cleaning of smaller parts e.g. in blast cabinets or workshop applications for example auto repair shops. Our short armor jacketed, straight bore boron / tungsten carbide nozzles are supplied as standard with 3/4" NPSM threads.

Medium length ATV venturi nozzles offer higher performance than short straight bore nozzles. How do ATV nozzles achieve this?

The answer is: UT nozzles have a straight bore; ATV nozzles have a venturi style bore. Having a venturi shaped bore increases exit velocity. Higher exit velocity means higher abrasive impact speeds & improved productivity. If you are using UT style nozzles and need higher performance, then look at our ATV nozzles. Available in a choice of Boron carbide or Tungsten carbide.

Choice of jacket styles and materials.

We offer a choice of different jackets to protect carbide sandblasting liners. From our all armored alloy jackets and threads that provide a very high level of protection against ricochet wear and impact to lighter weight thermoplastic plastic jackets that provide good impact protection for liners.

High Performance Nozzles:

Everblast makes a range of high quality Boron carbide High performance XLBC blast cleaning nozzles. These light weight nozzles have an advantage over other high performance nozzles in that they offer superior wear properties typical of boron carbide. These nozzles blast faster and are great to use when large surface areas need blast cleaning. They can be used for dry and wet blasting. Our Venturi Nozzles are available with either 1-1/4" NPSM fine threads or 2" coarse threads.

Angle Nozzles:

We offer a comprehensive range of angle nozzles that can direct abrasive flow at 45 degrees (approx) this is a great help when blast cleaning difficult to reach areas. These 45 degree sandblasting nozzles are available with one, two or three, forward shooting exit ports. We also offer a 1/2" O.D. blast cleaning probe for blast cleaning inside small (narrow) deep holes. Also avaible are 90 degree blast cleaning nozzles.

Wet Blasting:

Wet blasting and soda blast cleaning has become popular, as these methods offer a way of controlling dust - please see our range of Wet blasting nozzles. However, like many methods of blast cleaning there are pros and cons. It is important that each blast cleaning company researches to find out which method of blast cleaning (wet or dry) offers optimal results, given the type of surface preparation work being undertaken, abrasives used & coating that may subsequently be applied.

Guide on Estimated Nozzle Service Life in hours.

All figures are indicative and given for nozzle comparison purposes only. Actual nozzle service life will depend on operational variables, such as blast pressure, media dimensions and media particle profile. All figures are approximate.

Nozzle Liner Material	Steel/Grit Shot (hours)	Expendable Abrasives (Hours)	Aluminum Oxide (Hours)
Ceramic	20-40	10-30	1-4
Tungsten Carbide	500-800	300-400	20-40
Silicon Carbide/Silicon Nitride	600-1000	400-600	50-100
Silicon Composite	1400-2300	700-1450	180-900
Boron Carbide	1500-2500	750-1500	200 - 1000

Sandblasting nozzles for abrasive blast cleaning

Email us at: Sales@everblast.com